Phcc-pro-series E7 – E7 Series Sewage Pump Bedienungsanleitung PDF herunterladen

1806081 04/14

Model Discharge Max Amps Solid GPM / GPH Switch

No. HP Volts Diameter @ 10’ Handling @ 10’ Included

E7040-NS

10 120 2⬙ 6.3 2⬙ 74 / 4440 No Switch

E7040-VS

10 120 2⬙ 6.3 2⬙ 74 / 4440 Vertical Switch

E7040-USC3

10 120 2⬙ 6.3 2⬙ 74 / 4440 Ultimate Sensor

E7055-NS

2 120 2⬙ 7.0 2⬙ 89 / 5340 No Switch

E7055-VS

2 120 2⬙ 7.0 2⬙ 89 / 5340 Vertical Switch

E7055-USC3

2 120 2⬙ 7.0 2⬙ 89 / 5340 Ultimate Sensor

E7100-NS 1 120 2⬙ 12.8 2⬙ 114 / 6840 No Switch

E7100-VS 1 120 2⬙ 12.8 2⬙ 114 / 6840 Vertical Switch

Specifications

Important Safety Instructions and Warnings

SAVE THESE INSTRUCTIONS. This manual contains important SAFETY WARNINGS and

OPERATING INSTRUCTIONS for the PHCC Pro Series pumps. You will need to refer to it

before attempting any installation or maintenance.

ALWAYS keep these instructions with the unit so that they will be easily accessible.

Failure to read and follow these warnings and instructions could result in property

damage, serious injury, or death.

• ALWAYS disconnect the pump from the power source before servicing or making

adjustments.

• NEVER handle the pump or motor with wet hands or when standing on a wet or damp

surface while the pump is plugged into the power source.

• MAKE SURE THERE IS A PROPERLY GROUNDED RECEPTACLE AVAILABLE. This pump is

wired with a 3-prong grounded plug. To reduce the risk of electric shock, be certain

that it is only connected to a properly grounded, 3-prong receptacle. If you have a

2-prong receptacle, have a licensed electrician replace it with a 3-prong receptacle

according to local codes and ordinances.

• NEVER bypass grounding wires or remove the ground prong from the plug.

• DO NOT use an extension cord. The electrical outlet should be within the length of the

pump’s power cord, and at least 4 feet above the floor level to minimize potential

hazards from flood conditions.

• DO protect the electrical cord from sharp objects, hot surfaces, oil, and chemicals.

Avoid kinking the cord.

• MAKE SURE the supply circuit has a fuse or circuit breaker rated to handle the power

requirements noted on the nameplate of the pump.

• NEVER install the pump in locations classified as hazardous in accordance with the

National Electrical Code, ANSI/NFPA 70.

• DO NOT remove the power supply cord and strain relief or connect the pump directly to

the conduit.

• ALWAYS install the pump in accordance with the National Electric Code and all applicable

local codes and ordinances. All wiring should be performed by a licensed electrician.

• DO NOT use the power cord or strain relief to carry the pump. Use the pump handle.

• DO NOT expose the control unit to rain or snow.

• DO NOT operate the pump or control unit if it has been damaged in any way.

• DO drill an air bleed hole in the discharge pipe when a check valve is used. Drill

the hole at an upward angle from the bottom of the pit to avoid splashing water

outside the sump pit. If a hole is not drilled above the pump, an air lock may

prevent the pump from operating. The best location for the hole is about 3” above

the discharge outlet on the pump. The hole must

be drilled below the check valve.

Drill a 3/16” (4.76mm) hole in the discharge pipe for the E7 Series pumps.

• DO NOT disassemble the pump or control unit. When service is required, contact

Glentronics technical support at 800-991-0466, option 3. Return the product to the

manufacturer for any repairs at the following address:

Glentronics, Inc.

645 Heathrow Drive, Lincolnshire, IL 60069

• Sewage pumps will not provide protection during a power outage.

• After the initial installation, be sure to check the operation by filling the pit with water

and observing the pump operation through one full cycle.

• For continuous duty operation, the pump must be submerged at least ¾ of the depth of

the pump at all times.

• In instances where the discharge line is exposed to freezing temperatures, the pipe

must be sloped downward so any remaining water will drain out. Failure to do so will

prevent water from exiting the pit and damage the pump if the line freezes.

NOTICES

 CAUTION

 WARNING

To reduce the risk of hazards that can cause injury or

property damage, observe the following precautions.

Risk of electric shock.

To reduce this risk, observe the following precautions.

Water Alarm

Accidents happen…..water heaters rust and leak, laundry tubs overflow,

pipes break, and pumps seize. You can detect these leaks before they

become a major problem by placing a PHCC Pro Series Water Alarm

wherever there is a risk of water damage…..in the utility room, under the

kitchen sink, in the bathroom, or at the sump pit. The solid state

circuitry is reliable and extremely sensitive. The 110db alarm will sound

when as little as 1/32” of water reaches the sensor pad.

*Consult a licensed electrician.

If the above solutions do not solve the problem, contact Glentronics customer service 800-991-0466, option 3.

Troubleshooting

(Always unplug the pump from the controller before performing any maintenance)

Pump is not plugged in

Water is not high enough to activate the pump

Open circuit

Poor power source

Low voltage

Bad power cable

Locked impeller

Defective float switch

Defective pump

Locked impeller

Incorrect power supply

Overburdened due to heavy sand content in the water

Pump running continuously with no water present

Sensor mounted too low

Water flowing back from pipe

Malfunctioning sensor

Clogged or frozen discharge

Blocked intake strainer

Check valve installed with no air bleed hole in

pipe or pump

Check valve is stuck or installed upside down

Sensor rod is obstructed with large amount of debris

Check valve on secondary pump will not close

and water re-circulates within the system

Worn impeller

Partially blocked impeller

Clogged or frozen discharge

Broken or leaking pipe

Low power voltage

Check valve installed with no air bleed hole in

pipe or pump

Check valve is stuck or installed upside down

Pump is air locked

Check valve on secondary pump will not close

and water re-circulates within the system

Blocked intake screen

Broken impeller

Pump is experiencing an anti air lock safety

feature

The pump will not start or run

Thermal protector tripping or

not functioning

Pump starts and stops too

frequently

Pump will not shut off

Insufficient or no water

volume

Abnormal sound or vibration

Pump unexpectedly turns off

for 5 seconds (USC3 Only)

Plug pump in properly (see instructions)

Make sure float switch is positioned properly

Check circuit breaker or fuse

Check circuit line wires and cable*

Check line wires and source voltage*

Replace with new cable*

Remove strainer and clear obstruction

Replace float switch with new float switch

Replace pump with new pump

Remove strainer and clear obstruction

Check power supply source and voltage

Use water filter or replace with a higher wattage pump

Check sensor rod

Raise sensor or adjust timer

Install or replace check valve

Replace sensor

Clear blockage or thaw frozen line

Clear debris from intake strainer

Drill a bleed hole in the discharge pipe, or clean debris from the existing

hole in the pipe or pump

Reverse or replace check valve. Make sure the check valve is installed

with the flow arrow pointing up and out of the pit.

Clean debris from sensor rod

Replace the check valve on the secondary pump

Replace impeller & adjust spacing between impeller and cover

Remove strainer and clear obstruction

Clear blockage or thaw frozen line

Repair piping

Check power voltage, wires and cable condition

Drill a bleed hole in the discharge pipe, or clean debris from the existing

hole in the pipe or pump

Reverse or replace the check valve. Be sure check valve is installed with

flow arrow pointing up and out of the pit

Remove debris from the air bleed hole

Replace the check valve on the secondary pump

Clear debris from intake screen

Replace impeller with new one

Pump is frequently cycling on and off. The controller has a safety feature

that turns the pump off for 5 seconds if it detects a possible air lock.

This is normal. No action is required.

E7055

E7040

PHCC Pro Series

Sewage Pumps

Instruction Manual

& Safety Warnings

1 2 3 4

Inhaltsverzeichnis

Seite 1 - & Safety Warnings

Seite 2 - Limited Warranty

Installation InstructionsPrior to Installation1. Visually inspect your pump. Products may be damaged during shipping. If the producthas been damaged

Seite 3

Installation InstructionsPrior to Installation1. Visually inspect your pump. Products may be damaged during shipping. If the producthas been damaged

Seite 4

Kommentare zu diesen Handbüchern

Keine Kommentare

Phcc-pro-series E7 – E7 Series Sewage Pump Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Pumpen Phcc-pro-series E7 – E7 Series Sewage Pump herunter. PHCC Pro Series E7 – E7 Series Sewage Pump User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Pumpen Phcc-pro-series E7 – E7 Series Sewage Pump